Arkanoid槳（旋轉器）控制器

Spinner used in arcade veion of Arkanoid, Puchi Carat, etc. The controller was made with a 3D printer. Spinne are called paddles in Japan. Use the following parts in addition to the parts made by 3D printe. -3mm Metal shaft (aluminum in the example) 39 mm, 69 mm each. -608 bearing -M3x6mm screw Itallation of seor PCB. The mounting holes have the same dimeio as for arkanoids. Equivalent to Seimitsu Kogyo's MS base, the thickness of the screw hole is 4 mm. Since the shaft is normal and long, there are two types, so use it according to the environment. Two types of frames are available. Please use either the integrated type or the upper and lower division. The gear ratio of 14:38 is about 1:20 with 3 gea. The number of slits is 24. (Equivalent to arkanoid) Since there are 3 gea, if you use a PCB with 2 gea, the input will be reveed. Replace the wiring. By ierting an M16 nut in the knob, you can increase the weight and increase the inertia. Please itall it as you like. Please prepare the seor PCB separately -Diverted from other spinne It is intended for arkanoids or compatibles, but some may require mounting adjustments. -Make your own (material cost is about $ 2) Reference "Seor picture book for game board" in "Waikun's Mechanical Club" -Multi-seor board for paddle controller (1650 yen) Made by MarineDrivePcbWorkShop and available online. It works fine within the range I used, but I'm a breakout amateur, so I'd be happy if you could give me some impressio and improvements from people who are playing spinner games. －－－－－－－－ 街機版的生物堿、小型克拉等使用的槳控制器 在3D打印機上進行了完全劃痕。 因為槳價格高漲，所以制作了可以代替的。 除了3D打印機部件以外，還使用以下部件。 ?直徑3mm的金屬軸（作例中為鋁圓棒）39mm、69mm各1根 ?608軸承1個 ?用于固定M3x6mm螺釘傳感器基板。 安裝孔的尺寸與手持鏈烷烴相同。 與Semitsu工業MS基本相同，螺紋孔板厚4mm 軸和通常一樣長，所以有兩種，請配合環境使用。 框架請使用一體型和上下分割中喜歡的一方。 齒輪比14:38為3段，約1:20、24狹縫。（相當于鏈烷烴） 因為齒輪為3級，所以從齒輪2級的槳上挪用基板時，輸入左右相反。 請更換配線。 通過在旋鈕內放入M16螺母，可以增加重量，增強慣性。 請根據自己的喜好搭載。 ■請另外準備傳感器基板■ ?從其他槳挪用 設想用于鏈烷烴或互換品，根據物品的不同需要進行安裝調整。 ?自制（材料費200日元左右） 參考“小朋友的機械俱樂部”內“游戲基板用傳感器圖鑒” ?槳控制器用多傳感器基板（1650日元） MarineDrivePcbWorkShop先生制作，郵購能買到。 恐怕可以直接安裝，但實物還沒有確認。 雖然在自己使用的范圍內沒有問題地工作著，但是因為是破壞幾個街區的外行，所以能得到一定程度上玩槳游戲的人的感想和改善點的反饋，非常有幫助。